Step Instruction for Bathtub Installation
Step Instruction for Bathtub Installation
Blog Article
Everybody has their own individual theory in relation to How to Install a Bathtub.
Installing a bathtub isn't precisely rocket science, however it does need strong plumbing, woodworking, as well as often, tiling abilities. Changing an old bath tub with a brand-new one is also a reasonably tough project. If the old tub is readily obtainable, the project can relocate rapidly; if you have to open a wall to remove the old tub and also position the brand-new bathtub, the job is a lot harder. In either instance, the job is within a house handyman's skills, although you will certainly need a helper to leave the old bathtub as well as embeded in the new one. See to it you have certified on your own for the work as well as are comfortable trying it. As opposed to working with a specialist to take control of a halfway-completed task, it is far better to think about employing one prior to you begin. Chances are you may require a specialist plumber to make tube connections.
This post will certainly assist you set up a brand-new tub in your washroom if you have actually currently acquired a brand-new tub and don't require to transform the plan of your previous supply of water pipes.
Your devices as well as material list must make up the following:
Removing Old Touches
If you need to change old taps with new ones as a part of your installment, then the first thing you need to do is detach the water. After doing so, turn on the taps to drain any kind of water remaining in the system. The procedure of getting rid of the existing taps can be quite bothersome due to the limited gain access to that is commonly the case.
Use a container wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipes to the faucets. Have a cloth prepared for the remaining water that will come from the pipelines. As soon as the supply pipes have actually been eliminated, use the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to quit the solitary taps from turning throughout this procedure. When the taps have actually been gotten rid of, the holes in the bath/basin will have to be cleansed of any type of old sealing substance.
Prior to proceeding to fit the new faucets, contrast the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the brand-new taps to fit.
Suitable New Taps
If the tails of the brand-new faucets are plastic, then you will certainly need a plastic connector to avoid damages to the thread. One end of the connector fits on the plastic tail of the faucet and also the other end provides a connection to the current supply pipelines.
If you require to fit a monobloc, then you will certainly require decreasing couplers, which connects the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next off, place the tap in the placing hole in the bath/basin making certain that the washers are in area in between the tap and also the sink. Safeguard the faucet in place with the supplier provided backnut. Once the faucet is firmly in place, the supply pipelines can be connected to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with normal tap ports. The previous kind must be attached to the faucet finishes initially, tightening up only by hand. The supply pipes can later be connected to the other end. Tighten both ends with a spanner after both ends have actually been linked.
Setting up the Tub
Utilizing both wooden boards under its feet, place the bathtub in the required position. The wooden boards are valuable in uniformly spreading the weight of the bathtub over the location of the boards as opposed to focusing all the weight onto four tiny factors.
The next objective is to make certain that the tub is leveled all round. This can be achieved by examining the level and readjusting the feet on the tub until the level reads level.
To mount taps, fit all-time low of the furthest adaptable tap adapter to the appropriate supply pipeline by making a compression join; then do the exact same for the various other tap.
Turn on the water supply as well as examine all joints and brand-new pipework for leakages and tighten them if necessary. Fill the bathtub as well as also inspect the overflow electrical outlet as well as the typical electrical outlet for leakages.
Lastly, fix the bath paneling as described in the supplier's user's manual. Tiling and securing around the tub needs to wait up until the bathtub has actually been made use of a minimum of when as this will resolve it into its final placement.
Getting ready for the Installment
First of all, the supporting structure provided with the bathroom ought to be fitted (if needed) according to the supplier's directions. Next off, fit the faucets or mixer to the bathtub. When fitting the tap block, it is necessary to make sure that if the tap includes a plastic washing machine, it is fitted in between the bathroom as well as the faucets. On a plastic bathroom, it is also practical to fit a supporting plate under the taps system to prevent strain on the bathtub.
Fit the flexible tap adapters to the bottom of both taps using 2 nuts and olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet with the hole in the bath. Make use of the nut provided by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make certain you utilize all of the provided washers.
Connect the catch to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom should currently prepare to be fitted in its final position.
Tiling Around the Bathtub
In the location where the bath satisfies the tile, it is required to secure the joins with a silicone rubber caulking. This is necessary as the installation can move sufficient to break a stiff seal, causing the water to pass through the wall surface in between the bathroom and the tiling, resulting in problems with moisture and possible leaks to the ceiling below.
You can select from a selection of coloured sealants to blend in your fixtures and fittings. They are sold in tubes and also cartridges, and can securing spaces as much as a size of 3mm (1/8 inch). If you have a bigger void to fill up, you can fill it with twists of soaked paper or soft rope. Keep in mind to always load the bath tub with water prior to sealing, to permit the movement experienced when the tub is in use. The sealer can split fairly very early if you do not think about this activity before securing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are likewise easily readily available on the marketplace. It is advisable to fit the ceramic tiles making use of waterproof or water-proof sticky and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you appreciate reading about How to Install a Bathtub? Make a remark below. We will be interested to hear your suggestions about this write up. We are looking forward to see you back again in the future. Enjoyed reading our posting? Please share it. Let others discover it. Thank you so much for your time invested reading it.
Booking Report this page